在工業清洗領域，碳氫清洗機憑借對油脂、污漬的高效溶解能力，成為精密零件清洗的 “得力干將”。然而，其槽體長期接觸碳氫溶劑及被清洗工件攜帶的雜質，容易出現腐蝕、滲漏等問題，不僅影響清洗效果，更直接縮短設備使用壽命。要讓槽體在苛刻環境中保持 “強健體魄”，需要從材料選擇、表面防護、結構設計到使用維護的全流程精細呵護，構建一套立體化的抗腐蝕延壽體系。

　　In the field of industrial cleaning, hydrocarbon cleaning machines have become a powerful tool for precision parts cleaning due to their efficient ability to dissolve grease and stains. However, its tank body is prone to corrosion, leakage, and other problems due to long-term exposure to hydrocarbon solvents and impurities carried by the cleaned workpiece, which not only affects the cleaning effect but also directly shortens the service life of the equipment. To maintain a strong and robust body in harsh environments, it is necessary to carefully care for the entire process from material selection, surface protection, structural design to use and maintenance, and build a three-dimensional anti-corrosion and longevity system.

　　材料選擇：為槽體打造 “鋼筋鐵骨”

　　Material selection: Create a "steel and iron frame" for the groove body

　　槽體材料的耐腐蝕性是抗腐蝕的根基。碳氫溶劑本身化學性質穩定，但工件表面可能殘留水分、金屬離子、切削液等污染物，長期接觸會對槽體造成電化學腐蝕或化學侵蝕。因此，需根據清洗工況選擇適配材料：

　　The corrosion resistance of the tank material is the foundation of corrosion resistance. Carbon hydrogen solvents themselves have stable chemical properties, but there may be residual pollutants such as moisture, metal ions, and cutting fluids on the surface of the workpiece. Long term contact can cause electrochemical corrosion or chemical erosion to the tank body. Therefore, it is necessary to select suitable materials according to the cleaning conditions:

　　不銹鋼家族的 “抗蝕擔當”：304 不銹鋼（0Cr18Ni9）憑借良好的耐氧化性和性價比，成為普通工況首選，適用于清洗不含氯離子的碳氫溶劑（如正己烷、環己烷）；而在可能接觸到微量水分或含氯雜質的場景，需升級至 316L 不銹鋼（00Cr17Ni14Mo2），其添加的鉬元素使抗點蝕能力提升 50%，能抵御氯離子（耐受濃度≤200ppm）的侵蝕。

　　The "corrosion resistance responsibility" of the stainless steel family: 304 stainless steel (0Cr18Ni9) has become the preferred choice for ordinary working conditions due to its good oxidation resistance and cost-effectiveness, and is suitable for cleaning hydrocarbon solvents that do not contain chloride ions (such as n-hexane and cyclohexane); In scenarios where there is a possibility of exposure to trace amounts of moisture or chlorine containing impurities, it is necessary to upgrade to 316L stainless steel (00Cr17Ni14Mo2). The added molybdenum element increases the pitting corrosion resistance by 50% and can resist the erosion of chloride ions (tolerance concentration ≤ 200ppm).

　　非金屬材料的 “柔性防護”：聚丙烯（PP）和聚氯乙烯（PVC）等工程塑料槽體，在強酸性或強堿性碳氫清洗（如添加助洗劑的場景）中表現優異，PP 耐溫可達 100℃，適合中溫清洗（60-80℃），PVC 則對多數有機溶劑有良好耐受性，但耐溫較低（≤60℃），需根據清洗溫度合理選擇。

　　Flexible protection of non-metallic materials: Engineering plastic tanks such as polypropylene (PP) and polyvinyl chloride (PVC) perform well in strong acidic or strong alkaline hydrocarbon cleaning (such as scenarios with added detergents). PP can withstand temperatures up to 100 ℃ and is suitable for medium temperature cleaning (60-80 ℃), while PVC has good resistance to most organic solvents, but has lower temperature resistance (≤ 60 ℃), and should be selected reasonably according to the cleaning temperature.

　　表面處理：給槽體穿上 “防腐外衣”

　　Surface treatment: Coat the tank with an anti-corrosion coating

　　即使選用耐蝕材料，表面處理仍能進一步提升抗腐蝕性能：

　　Even with the use of corrosion-resistant materials, surface treatment can still further enhance corrosion resistance:

　　涂層防護：筑起化學屏障：在不銹鋼槽體內壁噴涂聚四氟乙烯（PTFE）或聚偏二氟乙烯（PVDF），形成 0.2-0.5mm 厚度的致密涂層，其耐化學腐蝕性幾乎涵蓋所有碳氫溶劑，且表面光滑不易掛料，減少雜質滯留導致的局部腐蝕；噴涂過程需控制涂層均勻性（厚度誤差≤±5%），并通過電火花檢漏儀檢測孔隙（電壓 15kV，無漏點為合格）。

　　Coating protection: Build a chemical barrier: Spray polytetrafluoroethylene (PTFE) or polyvinylidene fluoride (PVDF) on the inner wall of the stainless steel tank to form a dense coating with a thickness of 0.2-0.5mm. Its chemical corrosion resistance covers almost all hydrocarbon solvents, and the surface is smooth and not easy to hang, reducing local corrosion caused by impurity retention; The spraying process requires controlling the uniformity of the coating (thickness error ≤ ± 5%), and detecting pores through an electric spark leak detector (voltage 15kV, no leakage points are qualified).

　　金屬表面改性：強化原生耐蝕性：對不銹鋼槽體進行電解拋光或鈍化處理，電解拋光可將表面粗糙度降至 Ra≤0.2μm，減少雜質吸附；鈍化處理則通過硝酸溶液浸泡，使金屬表面生成更穩定的氧化膜，提升抗均勻腐蝕能力，處理后需用去離子水沖洗至中性（pH=6.5-7.5）。

　　Metal surface modification: Enhancing primary corrosion resistance: Electrolytic polishing or passivation treatment is applied to stainless steel tanks, which can reduce surface roughness to Ra ≤ 0.2 μ m and reduce impurity adsorption; Passivation treatment involves soaking the metal surface in nitric acid solution to form a more stable oxide film and enhance its resistance to uniform corrosion. After treatment, it needs to be rinsed with deionized water until neutral (pH=6.5-7.5).

　　結構設計：從源頭減少腐蝕隱患

　　Structural design: Reduce corrosion hazards from the source

　　合理的結構設計能避免液體滯留、應力集中等問題，降低腐蝕風險：

　　Reasonable structural design can avoid problems such as liquid retention and stress concentration, and reduce the risk of corrosion

　　導流與排空：讓液體 “來去自如”：槽體底部設計 3°-5° 傾斜角，并在最低處設置錐形排空口（直徑≥50mm），確保清洗結束后殘留液體快速排凈，避免溶劑長期滯留形成 “死水” 區域；內壁轉角處采用 R≥10mm 的圓弧過渡，減少直角縫隙中的雜質堆積，圓弧表面粗糙度需控制在 Ra≤0.4μm，便于清潔。

　　Diversion and emptying: allowing the liquid to come and go freely: the bottom of the tank is designed with a tilt angle of 3 ° -5 °, and a conical exhaust port (diameter ≥ 50mm) is set at the lowest point to ensure that residual liquid is quickly drained after cleaning, avoiding the formation of a "stagnant water" area due to long-term solvent retention; The inner wall corner adopts a circular arc transition with R ≥ 10mm to reduce the accumulation of impurities in the right angle gap. The surface roughness of the circular arc needs to be controlled within Ra ≤ 0.4 μ m for easy cleaning.

　　可拆卸與易更換：局部防護升級

　　Detachable and easy to replace: upgraded local protection

　　對于物料進出口、加熱管接口等易受沖刷的部位，采用可拆卸式法蘭連接，法蘭墊片選用耐碳氫溶劑的丁腈橡膠或氟橡膠（如 FKM），其溶脹率≤5%，避免墊片老化導致的泄漏；加熱管（如不銹鋼翅片管）與槽體接觸處設置絕緣套管（如聚醚醚酮 PEEK），防止不同金屬接觸形成電偶腐蝕。

　　For parts that are prone to erosion such as material import and export, heating pipe interfaces, etc., detachable flange connections are used. The flange gasket is made of nitrile rubber or fluororubber (such as FKM) that is resistant to hydrocarbon solvents, with a swelling rate of ≤ 5%, to avoid leakage caused by gasket aging; Insulation sleeves (such as polyetheretherketone PEEK) are installed at the contact between the heating tube (such as stainless steel finned tube) and the tank to prevent galvanic corrosion caused by contact between different metals.

　　使用維護：日常呵護的 “細節哲學”

　　Usage and Maintenance: The "Detail Philosophy" of Daily Care

　　正確的使用習慣是延長槽體壽命的關鍵，需從清洗參數控制到日常保養嚴格執行：

　　Correct usage habits are the key to extending the lifespan of the tank, and strict adherence to cleaning parameters and daily maintenance is required

　　清洗參數 “Goldilocks 原則”：溫度過高（超過溶劑沸點 10℃以上）會加劇溶劑揮發和槽體受熱應力影響，建議控制在溶劑沸點以下 5-10℃（如碳氫溶劑沸點 150℃，清洗溫度設為 140-145℃）；超聲波功率密度控制在 0.3-0.8W/cm?，過高的空化效應會導致槽體壁面產生微裂紋，成為腐蝕起點。

　　Cleaning parameter "Goldilocks principle": If the temperature is too high (more than 10 ℃ above the boiling point of the solvent), it will intensify solvent evaporation and the thermal stress of the tank. It is recommended to control it at 5-10 ℃ below the boiling point of the solvent (such as setting the cleaning temperature to 140-145 ℃ for hydrocarbon solvents with a boiling point of 150 ℃); Is the ultrasonic power density controlled between 0.3-0.8W/cm? Excessive cavitation effect can lead to microcracks on the wall of the tank, becoming the starting point of corrosion.

　　雜質控制：切斷腐蝕 “導火索”

　　Impurity control: Cut off the "fuse" of corrosion

　　工件進入清洗機前，需通過預清洗去除明顯的泥沙、金屬碎屑（殘留顆粒≤100μm），避免硬質顆粒劃傷槽體表面；定期（每班次結束后）用軟質毛刷（如尼龍刷）清理槽體底部沉積的金屬粉末、纖維雜質，頑固污漬可用弱堿性溶液（pH=8-9）浸泡 30 分鐘后沖洗，嚴禁使用鋼絲球等硬質工具損傷表面。

　　Before entering the cleaning machine, the workpiece needs to be pre cleaned to remove obvious sediment and metal debris (residual particles ≤ 100 μ m), to avoid scratching the surface of the groove with hard particles; Regularly (after each shift) use a soft brush (such as a nylon brush) to clean the metal powder and fiber impurities deposited at the bottom of the tank. Stubborn stains can be soaked in a weak alkaline solution (pH=8-9) for 30 minutes and then rinsed. It is strictly prohibited to use hard tools such as steel wire balls to damage the surface.

　　干燥防護：拒絕 “潮濕陷阱”

　　Dry protection: Reject "moisture traps"

　　長期停機前，需將槽體徹底排空并干燥：先用壓縮空氣（露點≤-20℃）吹掃內壁 5-10 分鐘，再開啟槽體加熱功能（溫度 50-60℃）保持 2 小時，確保無殘留水分；潮濕環境中存放時，可在槽內放置硅膠干燥劑（用量 500g / 立方米），并定期更換（吸濕率達 20% 時更換）。

　　Before long-term shutdown, the tank body needs to be completely emptied and dried: first blow the inner wall with compressed air (dew point ≤ -20 ℃) for 5-10 minutes, then turn on the heating function of the tank body (temperature 50-60 ℃) and keep it for 2 hours to ensure that there is no residual moisture; When stored in a humid environment, silica gel desiccant (500g/cubic meter) can be placed in the tank and replaced regularly (when the moisture absorption rate reaches 20%).

　　本文由碳氫清洗機友情奉獻.更多有關的知識請點擊:http://www.fdcyxzx.com我們將會對您提出的疑問進行詳細的解答，歡迎您登錄網站留言.

　　This article is a friendly contribution from CNC high-pressure cleaning machine For more information, please click: http://www.fdcyxzx.com We will provide detailed answers to your questions. You are welcome to log in to our website and leave a message